Laundromat Store Magnetic Lock Access Control Kit Wiring Instructions Video:
Features:
Electric Lock MAG-UL1200LSDM
Surface Mount UL Listed Single Door Magnetic Lock with 1200 pounds Holding Force.
• Mount Type - Surface Mount Single Door
• Dual Voltage Current Draw - 500mA/12V 250mA24V
• Holding Force - 1200 Lbs.
• Delay - Yes
• Weight - 12 lb.
• Lock Sensor - Yes
• LED - Yes
• Monitoring - Yes
• CE Approved - Yes
• Build-In Voltage Spike Suppressor - Yes
• UL Listed - Yes
• Dimentions - 10.5 x 2.9 x 1.6 inches
7 Day Timer 7DTIMER12VDC
12 Volt Weekly & Daily Digital Access Control Timer
This multipurpose programmable digital timer module is ideal for any application where time control is required.
Specifications:
• With 8 on/off programs up to 56 on/off setting up to 56 on/off programs for daily and weekly.
• Manual button for temporary override
• Micro-controller & CMOS quartz
• Led on/off indicate
• Accurate to the minute control
• Digital Time switch for 7 days - 24 hour
Features:
• Back up battery: 3 VDC lithium button cell
• Frequency: 50/60 Hz.
• Voltage: 100/130 VAC or 220/250 VAC
• Current 16(8) amps @ 250 VAC
• Rating: 30VDC/16A
• Voltage: 6,9,12,24V DC/AC
• Power Consumption: 3VA
• Operation temperature: 0 ° C - 55° C
Battery Back-Up MAG-12VDC7ABUPBOX
Model 12VDC7ABUPBOX Battery Back-Up System & Enclosure For Magnetic Lock. Includes Battery (12VDC 7 Amp), Switching Board, And Transformer (16 VAC 40 Amp transformer).Workable system for 6, 12 & 24VDC!
Extra Battery DCS-MA-004
Additional battery for battery back-up kits (Models 12VDC7ABUPBOX & 12VDC7ABUP using 12V / 7Ah battery.
Exit Motion Sensor BS-DS150I
The Bosch DS150i is specially designed for Request-to-Exit applications. The DS150i detects motion in its coverage area and signal an access control system or door control device.
The DS150i Series Exit Sensors are Passive Infrared Detectorsspecifically designed for “request to-exit” applications. They detect motion in their coverage area andsignal an access control system ordoor control device.
Features:
• UL Listed
• CE Approved
• Single or Double Door Use
• Selectable Relay Trigger Mode
• Wall and Ceiling Mountable
• Wrap-Around Coverage Pattern
• Selectable Fail Safe/Fail Secure
• Internal Vertical Pointability
• 12 or 24 AC or DC Operation
• Up to 60 Second Adjustable Latch Time
Specifications:
• POWER REQUIREMENTS 12 or 24 VAC or VDC, 26 mA @ 12 VDC
• COVERAGE 8 ft. by 10 ft. / 2.4 m by 3 mMOUNTING Surface Mount
• PATTERN POINTABILITY ±14° Vertical
• STORAGE & OPERATING TEMPERATURE -20° to +120°F / -29° to +50°C
• POWER LOSS DEFAULT Programmable Fail Safe or Fail Secure modes
• RELAY MODE Programmable retrigger or non-retrigger mode
• TEST FEATURES Externally visible activation LED
• RELAY OUTPUT Two Form “C” Contacts
• RELAY LATCH TIME Adjustable to 60 seconds
• DIMENSIONS 1.5" H., by 6.25" W., by 1.5" D. / 3.8 cm H., 15.8 cm W., 3.8cm
• RADIO FREQUENCY INTERFERENCE(RFI) IMMUNITY No alarm or setup on critical frequencies in the range from 26 to 1000 Megahertz at 50 v/m.
• LISTING UL Listing BP6245
Second Egress MAG-HPB4RER
Model MAG-HPB4RER Large Red Request To Exit Button
• Stainless Steel Face Plate
• Micro Switch: NO / NC
• Current Draw: 12VDC, 20mA
• Face Plate Dimension: 115L×70W×5H (mm) / 4.53” x 2.76” x 0.2”
Entrance Key Switch MAG-PB21K
Model PB21K Stainless Steel Key Switch with Two Keys Included.
This easy to operate key switch is perfect for use in any facility with access controlled entry/exit.
• Narrow design allows for easy installation
• Stainless Steel
• ON / OFF Function/Position
• Weather Resistant
• 1 Year Manufacturers Warranty
Approximate Dimensions:
Width X Length = 1 3/8" X 4"
All Magnetic Locks Include Armature Plate & Mounting Hardware For Basic Out-swing Applications. **Note: In-swing Doors require L & Z Brackets sold separately and available in our “Magnetic Lock Brackets” section.